Share
Results 1 to 12 of 12

Thread: Source for Wiring / extension cords

Hybrid View

  1. #1

    Default Source for Wiring / extension cords

    I do not have any affiliation with these guys, but they sell wire and cable products, including heavy duty RV extension cords. I have used them as a source for thin wall cross linked polyethelyne wiring for my race bike.


    http://www.wireandsupply.com/category_s/559.htm
    Last edited by sportbike; 03-03-2011 at 06:16 PM. Reason: Fixed Link
    Everlast 200DX
    Everlast PT185
    Shoptask 3-in-1 (not currently in my garage, but I own it...)

    Any day on a motorcycle like this that ends just needing parts and labor is a good day.
    4.93, 155.17mph 1/8th mile 7.497, 194.27mph 1/4 mile

  2. #2

    Default

    Thats a bad link.
    Gerald

    Millermatic 251
    Spectrum 300 Plasma
    Everlast PowerTig 250EX
    Everlast PowerCool W300
    Harris / Victor OA
    Craftsman 13 Speed Drill Press
    ProTools Air/Hydraulic Bender
    48" Brake
    Compressor, Notchers, Grinders, etc.

  3. #3

    Default

    90 cents a foot for 6awg thhn...home depot has a better price then that if you buy the 500' spool. Also found a seller on ebay that has 6awg by the foot for 79 cents a foot shipped
    sold my miller mig
    got a PT250EX
    saving up for a plasma cutter

  4. #4

    Default

    Quote Originally Posted by dgarnier View Post
    90 cents a foot for 6awg thhn...home depot has a better price then that if you buy the 500' spool. Also found a seller on ebay that has 6awg by the foot for 79 cents a foot shipped
    That is not a bad price. At .79, figure just under $20 for 25 feet and add the plugs $20-40.
    Mike R.
    Email: everlast@us-it.net
    www.everlastgenerators.com
    www.everlastwelders.com
    877-755-9353 x203
    M-F 12 - 7PM PST
    FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.

  5. #5

    Default

    I wish it was only 25'...my drier outlet is on the other side of the house from the panel so I have a 76' run. home depot is have good prices on the 50amp 250volt 4 wire plug and outlet. Got the new box installed today and going to order wire Monday.
    sold my miller mig
    got a PT250EX
    saving up for a plasma cutter

  6. #6

    Default

    DGarnier, make sure to do your homework before running cable that long. Somewhere on here is a calculator that'll tell you what gage wire to use for extended cable distances...
    PowerTig 225LX
    PowerCool W300
    PowerPlasma 60S
    Miller 140 MIG

  7. #7

    Default

    I am absolutley envious. I want a dedicated plug so bad for my welder, lol. Its so bad now I have a technique for pulling out the dryer plug from the back of it. Unfortunatley, money is prioritized at this moment in time.
    Frank

    I have a 250 EX welder and several other machines and equipment to allow for small scale manufacturing and prototyping of inventions

    I am located in Oregon about 20 minutes west of Portland

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •